# | Title | Journal | Year | Citations |
---|
1 | Performance, Combustion and Emission Characteristics of a D.I. Diesel Engine Fuelled with Nanoparticle Blended Jatropha Biodiesel | Periodica Polytechnica, Mechanical Engineering | 2015 | 78 |
2 | Bisection method in higher dimensions and the efficiency number | Periodica Polytechnica, Mechanical Engineering | 2012 | 71 |
3 | Applicability of friction stir welding in polymeric materials | Periodica Polytechnica, Mechanical Engineering | 2007 | 67 |
4 | Influence of the 3D Printing Process Settings on Tensile Strength of PLA and HT-PLA | Periodica Polytechnica, Mechanical Engineering | 2020 | 58 |
5 | Producing metal matrix syntactic foams by pressure infiltration | Periodica Polytechnica, Mechanical Engineering | 2008 | 53 |
6 | Analysis of Characteristics of Surface Roughness of Machined CFRP Composites | Periodica Polytechnica, Mechanical Engineering | 2019 | 51 |
7 | Increasing of Equipment Efficiency by Intensification of Technological Processes | Periodica Polytechnica, Mechanical Engineering | 2018 | 44 |
8 | On the Modeling of Surface Roughness and Cutting Force when Turning of Inconel 718 Using Artificial Neural Network and Response Surface Methodology: Accuracy and Benefit | Periodica Polytechnica, Mechanical Engineering | 2017 | 38 |
9 | Estimation of the Reliability of Automatic Axial-balancing Devices for Multistage Centrifugal Pumps | Periodica Polytechnica, Mechanical Engineering | 2018 | 31 |
10 | Analysis of Control System of Fuel Combustion in Boilers with Oxygen Sensor | Periodica Polytechnica, Mechanical Engineering | 2019 | 31 |
11 | Water purification of arsenic-contaminated drinking water via air gap membrane distillation (AGMD) | Periodica Polytechnica, Mechanical Engineering | 2014 | 30 |
12 | Grey Relational Analysis and Anova to Determine the Optimum Process Parameters for Friction Stir Welding of Ti and Mg Alloys | Periodica Polytechnica, Mechanical Engineering | 2018 | 30 |
13 | Optimization of Cutting Parameters to Minimize the Surface Roughness in the End Milling Process Using the Taguchi Method | Periodica Polytechnica, Mechanical Engineering | 2017 | 29 |
14 | PSI and TOPSIS Based Selection of Process Parameters in WEDM | Periodica Polytechnica, Mechanical Engineering | 2017 | 28 |
15 | Effect of the Fins Length for the Passive Cooling of the Photovoltaic Panels | Periodica Polytechnica, Mechanical Engineering | 2016 | 26 |
16 | Heat and Mass Transfer of a Peristaltic Electro-osmotic Flow of a Couple Stress Fluid through an Inclined Asymmetric Channel with Effects of Thermal Radiation and Chemical Reaction | Periodica Polytechnica, Mechanical Engineering | 2021 | 25 |
17 | Two-Dimensional Finite Element Analysis of Turning Processes | Periodica Polytechnica, Mechanical Engineering | 2017 | 24 |
18 | Prospects of Using Hydrodynamic Cavitation for Enhancement of Efficiency of Fluid Working Medium Preparation Technologies | Periodica Polytechnica, Mechanical Engineering | 2018 | 24 |
19 | Human Weaknesses and strengths in collaboration with robots | Periodica Polytechnica, Mechanical Engineering | 2008 | 23 |
20 | Development and Comparison of Quantitative Phase Analysis for Duplex Stainless Steel Weld | Periodica Polytechnica, Mechanical Engineering | 2018 | 23 |
21 | Multi Response Optimization of Setting Input Variables for Getting Better Product Quality in Machining of Magnesium AM60 by Grey Relation Analysis and ANOVA | Periodica Polytechnica, Mechanical Engineering | 0 | 23 |
22 | Back Propagation Neural Network for Prediction of Some Shell Moulding Parameters | Periodica Polytechnica, Mechanical Engineering | 2016 | 21 |
23 | Multi-Objective Optimization of Wire Electro Discharge Machining (WEDM) Process Parameters Using Grey-Fuzzy Approach | Periodica Polytechnica, Mechanical Engineering | 2018 | 21 |
24 | Development and mechanical properties of carbon fibre reinforced EP/VE hybrid composite systems | Periodica Polytechnica, Mechanical Engineering | 2014 | 18 |
25 | Mechanical, Thermal and Morphological Properties of Injection Molded Poly(lactic acid)/Calcium Carbonate Nanocomposites | Periodica Polytechnica, Mechanical Engineering | 2016 | 17 |
26 | Design and Analysis of 3D Printable Foot Prosthesis | Periodica Polytechnica, Mechanical Engineering | 2017 | 17 |
27 | Heat Transfer in Air Flow Past a Bottom Channel Wall-Attached Diamond-Shaped Baffle – Using a CFD Technique | Periodica Polytechnica, Mechanical Engineering | 2019 | 17 |
28 | Aerodynamics and Heat Transfer over Solid-Deflectors in Transverse, Staggered, Corrugated-Upstream and Corrugated-Downstream Patterns | Periodica Polytechnica, Mechanical Engineering | 2018 | 15 |
29 | Wear simulation of a reciprocating seal by global remeshing | Periodica Polytechnica, Mechanical Engineering | 2010 | 14 |
30 | Fatigue Behavior of Short Glass Fiber Reinforced Polyamide 66: Experimental Study and Fatigue Damage Modelling | Periodica Polytechnica, Mechanical Engineering | 2016 | 14 |
31 | Vibration Analysis of Carbon Fiber Reinforced Laminated Composite Skin with Glass Honeycomb Sandwich Beam Using HSDT | Periodica Polytechnica, Mechanical Engineering | 2017 | 14 |
32 | Structural Damages in Syntactic Metal Foams Caused by Monotone or Cyclic Compression | Periodica Polytechnica, Mechanical Engineering | 2017 | 14 |
33 | Cross Effect of Natural Rubber and Annealing on the Properties of Poly(Lactic Acid) | Periodica Polytechnica, Mechanical Engineering | 2019 | 14 |
34 | Investigation of Flame Retardant rPET Foam | Periodica Polytechnica, Mechanical Engineering | 2019 | 14 |
35 | The Effect of Machining Parameters and Optimization of Temperature Rise in Turning Operation of Aluminium-6061 Using RSM and Artificial Neural Network | Periodica Polytechnica, Mechanical Engineering | 2021 | 14 |
36 | Basins of attraction in a harmonically excited spherical bubble model. | Periodica Polytechnica, Mechanical Engineering | 2012 | 14 |
37 | On the microstructure of ceramic hollow microspheres | Periodica Polytechnica, Mechanical Engineering | 2010 | 13 |
38 | Beamforming measurements of an axial fan in an industrial environment | Periodica Polytechnica, Mechanical Engineering | 2013 | 13 |
39 | Analytical and Numerical Solutions of the Rotor Flow in Tesla Turbines | Periodica Polytechnica, Mechanical Engineering | 2017 | 13 |
40 | Numerical Modelling and Optimization of Dry Orthogonal Turning of Al6061 T6 Alloy | Periodica Polytechnica, Mechanical Engineering | 2018 | 13 |
41 | Investigation of Tribological Properties of Two-Component Bidisperse Epoxy-Polyester Composite Materials for Its Use in the Friction Units of Means of Sea Transport | Periodica Polytechnica, Mechanical Engineering | 2019 | 13 |
42 | Chemical etching of titanium samples | Periodica Polytechnica, Mechanical Engineering | 2013 | 12 |
43 | Experimental Model for the Main Cutting Force in Face Milling of a High Strength Structural Steel | Periodica Polytechnica, Mechanical Engineering | 2015 | 12 |
44 | Evaporation of Renewable Fuels in a Lean Premixed Prevaporized Burner | Periodica Polytechnica, Mechanical Engineering | 2016 | 12 |
45 | Validation of a Discrete Model for Flow Distribution in Dividing-Flow Manifolds: Numerical and Experimental Studies | Periodica Polytechnica, Mechanical Engineering | 2016 | 12 |
46 | Theoretical Analysis of Continuous Heat Extraction from Absorber of Solar Still for Improving the Productivity | Periodica Polytechnica, Mechanical Engineering | 2018 | 12 |
47 | Single and Hybrid Nanofluids to Enhance Performance of Flat Plate Solar Collectors: Application and Obstacles | Periodica Polytechnica, Mechanical Engineering | 2020 | 12 |
48 | Computer tomography based reconstruction of metal matrix syntactic foams | Periodica Polytechnica, Mechanical Engineering | 2014 | 11 |
49 | Numerical Analysis of Thermal and Aerodynamic Fields in a Channel with Cascaded Baffles | Periodica Polytechnica, Mechanical Engineering | 2017 | 11 |
50 | Design, Construction and Performance Study of a Solar Assisted Tri-cycle | Periodica Polytechnica, Mechanical Engineering | 2017 | 11 |