| 1 | A review of laser welding techniques for magnesium alloys | Journal of Materials Processing Technology | 2006 | 558 |
| 2 | Strain hardening behavior of a friction stir welded magnesium alloy | Scripta Materialia | 2007 | 405 |
| 3 | A comprehensive review on laser powder bed fusion of steels: Processing, microstructure, defects and control methods, mechanical properties, current challenges and future trends | Journal of Manufacturing Processes | 2022 | 397 |
| 4 | Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy | Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing | 2008 | 332 |
| 5 | Wear mechanisms and tool life management of WC–Co drills during dry high speed drilling of woven carbon fibre composites | Wear | 2009 | 258 |
| 6 | Laser polishing of selective laser melted components | International Journal of Machine Tools and Manufacture | 2015 | 256 |
| 7 | Effect of welding speed on butt joint quality of Ti–6Al–4V alloy welded using a high-power Nd:YAG laser | Optics and Lasers in Engineering | 2009 | 195 |
| 8 | Review of defects in lattice structures manufactured by powder bed fusion | International Journal of Advanced Manufacturing Technology | 2019 | 195 |
| 9 | The nucleation of Fe-Rich phases on oxide films in Al-11.5Si-0.4Mg cast alloys | Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science | 2003 | 194 |
| 10 | Experimental study of shot peening and stress peen forming | Journal of Materials Processing Technology | 2010 | 185 |
| 11 | Laser-assisted high-speed finish turning of superalloy Inconel 718 under dry conditions | CIRP Annals - Manufacturing Technology | 2010 | 158 |
| 12 | Process optimisation and mechanical properties of friction stir lap welds of 7075-T6 stringers on 2024-T3 skin | Materials & Design | 2010 | 153 |
| 13 | Tensile properties of a friction stir welded magnesium alloy: Effect of pin tool thread orientation and weld pitch | Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing | 2010 | 151 |
| 14 | An analytical approach to relate shot peening parameters to Almen intensity | Surface and Coatings Technology | 2010 | 144 |
| 15 | The solidification characteristics of Fe-rich intermetallics in Al-11.5Si-0.4Mg cast alloys | Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science | 2004 | 142 |
| 16 | Atomistics of pre-nucleation layering of liquid metals at the interface with poor nucleants | Communications Chemistry | 2019 | 139 |
| 17 | Laser assisted turning of Titanium Metal Matrix Composite | CIRP Annals - Manufacturing Technology | 2011 | 115 |
| 18 | Tensile properties and strain-hardening behavior of double-sided arc welded and friction stir welded AZ31B magnesium alloy | Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing | 2010 | 114 |
| 19 | Characterization of the dry high speed drilling process of woven composites using Machinability Maps approach | CIRP Annals - Manufacturing Technology | 2009 | 113 |
| 20 | Polishing-assisted galvanic corrosion in the dissimilar friction stir welded joint of AZ31 magnesium alloy to 2024 aluminum alloy | Materials Characterization | 2009 | 110 |
| 21 | Distortion prediction and compensation in selective laser melting | Additive Manufacturing | 2017 | 101 |
| 22 | Lap shear strength and fatigue life of friction stir spot welded AZ31 magnesium and 5754 aluminum alloys | Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing | 2012 | 99 |
| 23 | High Energy Fluid Jet Machining (HEFJet-Mach): From scientific and technological advances to niche industrial applications | CIRP Annals - Manufacturing Technology | 2014 | 99 |
| 24 | Shot peening and peen forming finite element modelling – Towards a quantitative method | International Journal of Solids and Structures | 2011 | 98 |
| 25 | Manufacturing classification system in the real world: factors influencing manufacturing process choices for filed commercial oral solid dosage formulations, case studies from industry and considerations for continuous processing | Pharmaceutical Development and Technology | 2018 | 92 |
| 26 | A review of automated solar photovoltaic defect detection systems: Approaches, challenges, and future orientations | Solar Energy | 2023 | 92 |
| 27 | Friction Stir Welded AZ31 Magnesium Alloy: Microstructure, Texture, and Tensile Properties | Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science | 2012 | 89 |
| 28 | Robust fabrication of μ-patterns with tunable and durable wetting properties: hydrophilic to ultrahydrophobic via a vacuum process | Journal of Materials Chemistry A | 2017 | 89 |
| 29 | Characterization and optimization of orbital drilling of woven carbon fiber reinforced epoxy laminates | CIRP Annals - Manufacturing Technology | 2012 | 88 |
| 30 | Facile, one-pot biosynthesis and characterization of iron, copper and silver nanoparticles using Syzygium cumini leaf extract: As an effective antimicrobial and aflatoxin B1 adsorption agents | PLoS ONE | 2020 | 86 |
| 31 | A conceptual framework for the ubiquitous factory | International Journal of Production Research | 2012 | 83 |
| 32 | Linear friction welding of a near-β titanium alloy | Acta Materialia | 2012 | 83 |
| 33 | Deep learning-based construction equipment operators’ mental fatigue classification using wearable EEG sensor data | Advanced Engineering Informatics | 2023 | 82 |
| 34 | Assessment of trapped powder removal and inspection strategies for powder bed fusion techniques | International Journal of Advanced Manufacturing Technology | 2020 | 80 |
| 35 | Resistance welding of thermoplastic composites skin/stringer joints | Composites Part A: Applied Science and Manufacturing | 2007 | 78 |
| 36 | Application of lignin in controlled release: development of predictive model based on artificial neural network for API release | Cellulose | 2019 | 78 |
| 37 | Deep learning-based networks for automated recognition and classification of awkward working postures in construction using wearable insole sensor data | Automation in Construction | 2022 | 78 |
| 38 | Effect of preheating on the thermal, microstructural and mechanical properties of selective electron beam melted Ti-6Al-4V components | Materials and Design | 2019 | 76 |
| 39 | The FFC-Cambridge Process for Titanium Metal Winning | Key Engineering Materials | 2010 | 74 |
| 40 | A critical evaluation of the microstructural gradient along the build direction in electron beam melted Ti-6Al-4V alloy | Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing | 2019 | 74 |
| 41 | Finite element simulation of residual stresses induced by the dissimilar welding of a P92 steel pipe with weld metal IN625 | International Journal of Pressure Vessels and Piping | 2013 | 71 |
| 42 | Effect of iron and manganese contents on convection-free precipitation and sedimentation of primary -Al(FeMn)Si phase in liquid Al-11.5Si-0.4Mg alloy | Journal of Materials Science | 2004 | 70 |
| 43 | High Speed EDM and Laser Drilling of Aerospace Alloys | Procedia CIRP | 2016 | 70 |
| 44 | Characteristics of micro-hole formation during fibre laser drilling of aerospace superalloy | Precision Engineering | 2019 | 70 |
| 45 | Effect of Interfacial Reaction on the Mechanical Performance of Steel to Aluminum Dissimilar Ultrasonic Spot Welds | Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science | 2015 | 69 |
| 46 | Effect of Mn, Si, and Cooling Rate on the Formation of Iron-Rich Intermetallics in 206 Al-Cu Cast Alloys | Metallurgical and Materials Transactions B: Process Metallurgy and Materials Processing Science | 2012 | 67 |
| 47 | Decolouration of textile dyes in wastewaters by photocatalysis with TiO2 | Solar Energy | 2005 | 65 |
| 48 | Laser Processing of Hard and Ultra-Hard Materials for Micro-Machining and Surface Engineering Applications | Micromachines | 2021 | 65 |
| 49 | Metal mesh heating element size effect in resistance welding of thermoplastic composites | Journal of Composite Materials | 2012 | 63 |
| 50 | On the design workflow of auxetic metamaterials for structural applications | Smart Materials and Structures | 2022 | 63 |
