| 1 | A detailed insight into rate of water absorption of concrete: Experimental and modelling approach | 6.5 | 11 | Citations (PDF) |
| 2 | Biochar in cementitious composites: A comprehensive review of properties, compatibility, and prospect of use in sustainable geopolymer concrete | 2.3 | 18 | Citations (PDF) |
| 3 | Monitoring of chemical-assisted healing of fine cracks in concrete using ultrasonics and infrared thermographic techniques | 2.3 | 6 | Citations (PDF) |
| 4 | Blended cement and mortar with various low-calcium ground coal bottom ash content: Engineering characteristics, embodied carbon and cost analysis | 5.8 | 19 | Citations (PDF) |
| 5 | Review on effect of curing methods on high strength concrete | 5.8 | 59 | Citations (PDF) |
| 6 | Nondestructive Evaluation of Autonomic Crack Healing in Concrete Using Ultrasonic Wave Propagation | 1.9 | 3 | Citations (PDF) |
| 7 | Influence of coal bottom ash aggregate grading on properties of GGBS binary blended cement mortar | 1.2 | 4 | Citations (PDF) |
| 8 | Review on the effect of sewage sludge ash on the properties of concrete | 5.8 | 34 | Citations (PDF) |
| 9 | Optimizing aggregate grading and residual mortar coefficient in low-cement concrete by using crushed coal mine waste rock as base layers for low-traffic roads | 5.8 | 6 | Citations (PDF) |
| 10 | Structural health monitoring of timber bridges – A review | 5.8 | 44 | Citations (PDF) |
| 11 | Microstructural analysis of geopolymer pastes contaminated with crude oil: Impact on efflorescence, physical properties, and mechanical performance | 5.8 | 2 | Citations (PDF) |
| 12 | A Review on the Effect of Synthetic Fibres, Including Macro Fibres, on the Thermal Behaviour of Fibre-Reinforced Concrete | 2.0 | 12 | Citations (PDF) |
| 13 | Environmental Technology | 1.5 | 14 | Citations (PDF) |
| 14 | Influence of milling parameters on the properties of ground coal bottom ash and its blended cement | 5.8 | 28 | Citations (PDF) |
| 15 | Rubberized cement-stabilized aggregates: Mechanical performance, thermal properties, and effect on temperature fluctuation in road pavements | 3.6 | 16 | Citations (PDF) |
| 16 | Durability assessment of sustainable metakaolin based high strength concrete incorporating crumb tire rubber | 2.3 | 12 | Citations (PDF) |
| 17 | Properties of ultra-high performance concrete and conventional concrete with coal bottom ash as aggregate replacement and nanoadditives: A review | 2.0 | 10 | Citations (PDF) |
| 18 | Long term durability assessment of self-compacting concrete made with crushed recycled glass and metakaolin | 5.8 | 13 | Citations (PDF) |
| 19 | Removal of alkalinity and metal toxicity from incinerated biomedical waste ash by using Bacillus halodurans | 0.9 | 9 | Citations (PDF) |
| 20 | Properties of sustainable self-compacting concrete made with rice husk ash | 1.7 | 27 | Citations (PDF) |
| 21 | Effectiveness of using Metakaolin and fly ash as supplementary cementitious materials in pervious concrete | 1.7 | 37 | Citations (PDF) |
| 22 | Effect of alum sludge ash on the high-temperature resistance of mortar | 7.6 | 45 | Citations (PDF) |
| 23 | Strength and Permeability of No-Fines Concrete Made with Supplementary Cementitious Materials | 1.9 | 15 | Citations (PDF) |
| 24 | Clayey soil stabilization using alkali-activated volcanic ash and slag | 6.6 | 249 | Citations (PDF) |
| 25 | Properties of ternary blended cement containing ground granulated blast furnace slag and ground coal bottom ash | 5.8 | 54 | Citations (PDF) |
| 26 | Coal bottom ash as constituent binder and aggregate replacement in cementitious and geopolymer composites: A review | 2.3 | 24 | Citations (PDF) |
| 27 | Durability performance of self-compacting concrete made with waste foundry sand | 2.2 | 12 | Citations (PDF) |
| 28 | Reutilization of textile sludge stabilized with low grade-MgO as a replacement of cement in mortars | 5.8 | 22 | Citations (PDF) |
| 29 | Utilisation of crumb tire rubber in development of sustainable metakaolin based high strength concrete | 5.8 | 17 | Citations (PDF) |
| 30 | Utilization of crushed recycled glass and metakaolin for development of self-compacting concrete | 5.8 | 29 | Citations (PDF) |
| 31 | Mechanical performance and phase analysis of an eco-friendly alkali-activated binder made with sludge waste and blast-furnace slag | 7.0 | 60 | Citations (PDF) |
| 32 | The use of waste marble for cleaner production of structural concrete: A comprehensive experimental study | 5.8 | 35 | Citations (PDF) |
| 33 | A comprehensive taxonomy for structure and material deficiencies, preventions and remedies of timber bridges | 2.3 | 27 | Citations (PDF) |
| 34 | The potential use of drinking water sludge ash as supplementary cementitious material in the manufacture of concrete blocks | 7.6 | 77 | Citations (PDF) |
| 35 | Sustainable and Greener Self-Compacting Concrete incorporating Industrial By-Products: A Review | 7.0 | 136 | Citations (PDF) |
| 36 | Untreated rice husk ash incorporated high strength self-compacting concrete: Properties and environmental impact assessments | 3.2 | 32 | Citations (PDF) |
| 37 | Recycling of spent coffee grounds in construction materials: A review | 7.0 | 159 | Citations (PDF) |
| 38 | Thermal and environmental impact analysis of rice husk ash-based mortar as insulating wall plaster | 5.8 | 63 | Citations (PDF) |
| 39 | Experimental studies and drying shrinkage prediction model for concrete containing waste foundry sand | 3.2 | 28 | Citations (PDF) |
| 40 | Recycling of landfill wastes (tyres, plastics and glass) in construction – A review on global waste generation, performance, application and future opportunities | 7.6 | 528 | Citations (PDF) |
| 41 | Sulfate Resistance and Drying Shrinkage of Self-Compacting Concrete Incorporating Copper Slag | 1.9 | 17 | Citations (PDF) |
| 42 | Recycling copper slag in steel fibre concrete for sustainable construction | 7.0 | 66 | Citations (PDF) |
| 43 | Durability characteristics of self-compacting concrete made with copper slag | 5.8 | 129 | Citations (PDF) |
| 44 | Utilization of drinking water treatment sludge in concrete paving blocks: Microstructural analysis, durability and leaching properties | 6.3 | 103 | Citations (PDF) |
| 45 | Utilization of treated saw dust in concrete as partial replacement of natural sand | 7.0 | 49 | Citations (PDF) |
| 46 | Properties and microstructure of concrete blocks incorporating drinking water treatment sludge exposed to early-age carbonation curing | 7.0 | 90 | Citations (PDF) |
| 47 | Fly ash and ground granulated blast furnace slag-based alkali-activated concrete: Mechanical, transport and microstructural properties | 5.8 | 220 | Citations (PDF) |
| 48 | Application of rubberized cement-based composites in pavements: Suitability and considerations | 5.8 | 53 | Citations (PDF) |
| 49 | Influence of incinerated biomedical waste ash on the properties of concrete | 5.8 | 73 | Citations (PDF) |
| 50 | Strength and micro-structural properties of self-compacting concrete incorporating copper slag | 5.8 | 92 | Citations (PDF) |
| 51 | Strength properties and microstructural analysis of self-compacting concrete incorporating waste foundry sand | 5.8 | 59 | Citations (PDF) |
| 52 | Influence of marble waste as partial replacement of fine aggregates on strength and drying shrinkage of concrete | 5.8 | 89 | Citations (PDF) |
| 53 | Strength, permeation and micro-structural characteristics of concrete incorporating waste marble | 5.8 | 122 | Citations (PDF) |
| 54 | Utilization of textile sludge in cement mortar and paste | 5.8 | 48 | Citations (PDF) |
| 55 | Monitoring early-age setting of silica fume concrete using wave propagation techniques | 5.8 | 36 | Citations (PDF) |
| 56 | Recycle option for metallurgical by-product (Spent Foundry Sand) in green concrete for sustainable construction | 7.0 | 108 | Citations (PDF) |
| 57 | Sustainable geopolymer concrete using ground granulated blast furnace slag and rice husk ash: Strength and permeability properties | 7.0 | 304 | Citations (PDF) |
| 58 | Application of Recycled Ceramic Aggregates for the Production of Mineral-Asphalt Mixtures | 2.1 | 26 | Citations (PDF) |
| 59 | Durability properties of self-compacting concrete incorporating metakaolin and rice husk ash | 5.8 | 148 | Citations (PDF) |
| 60 | Strength, permeability and micro-structural characteristics of low-calcium fly ash based geopolymers | 5.8 | 116 | Citations (PDF) |
| 61 | Sulfuric acid resistance of fly ash based geopolymer concrete | 5.8 | 332 | Citations (PDF) |
| 62 | Influence of various parameters on strength and absorption properties of fly ash based geopolymer concrete designed by Taguchi method | 5.8 | 105 | Citations (PDF) |
| 63 | Properties of low-calcium fly ash based geopolymer concrete incorporating OPC as partial replacement of fly ash | 5.8 | 231 | Citations (PDF) |
| 64 | Model for mix design of brick aggregate concrete based on neural network modelling | 5.8 | 72 | Citations (PDF) |
| 65 | The use of zeolite, lightweight aggregate and boiler slag in restoration renders | 5.8 | 46 | Citations (PDF) |
| 66 | Effect of bacteria on strength, permeation characteristics and micro-structure of silica fume concrete | 5.8 | 138 | Citations (PDF) |
| 67 | Strength and micro-structural properties of self-compacting concrete containing metakaolin and rice husk ash | 5.8 | 69 | Citations (PDF) |
| 68 | Influence of rice husk ash (RHA) on the properties of self-compacting concrete: A review | 5.8 | 197 | Citations (PDF) |
| 69 | Properties of hydrophobised lightweight mortars with expanded cork | 5.8 | 56 | Citations (PDF) |
| 70 | Bacterial treatment of alkaline cement kiln dust using strain KG1 | 1.2 | 16 | Citations (PDF) |
| 71 | Influence of Bacterial-Treated Cement Kiln Dust on Strength and Permeability of Concrete | 1.9 | 36 | Citations (PDF) |
| 72 | An overview of geopolymers derived from industrial by-products | 5.8 | 367 | Citations (PDF) |
| 73 | Strength properties and micro-structural analysis of self-compacting concrete made with iron slag as partial replacement of fine aggregates | 5.8 | 73 | Citations (PDF) |
| 74 | Characterization of lightweight mortars containing wood processing by-products waste | 5.8 | 117 | Citations (PDF) |
| 75 | Effect of iron slag as partial replacement of fine aggregates on the durability characteristics of self-compacting concrete | 5.8 | 84 | Citations (PDF) |
| 76 | Durability Properties of Concrete Made with High Volumes of Low-Calcium Coal Bottom Ash As a Replacement of Two Types of Sand | 1.9 | 27 | Citations (PDF) |
| 77 | Properties of bacterial rice husk ash concrete | 5.8 | 266 | Citations (PDF) |
| 78 | Sodium sulfate and alternative combined sulfate/chloride action on ordinary and self-consolidating PLC-based concretes | 5.8 | 27 | Citations (PDF) |
| 79 | Influence of bacteria on compressive strength and permeation properties of concrete made with cement baghouse filter dust | 5.8 | 120 | Citations (PDF) |
| 80 | Strength and permeation properties of self-compacting concrete containing fly ash and hooked steel fibres | 5.8 | 84 | Citations (PDF) |
| 81 | Effect of coal bottom ash as partial replacement of sand on workability and strength properties of concrete | 7.0 | 239 | Citations (PDF) |
| 82 | Strength, permeability and microstructure of self-compacting concrete containing rice husk ash | 5.0 | 267 | Citations (PDF) |
| 83 | Properties of concrete containing high volumes of coal bottom ash as fine aggregate | 7.0 | 195 | Citations (PDF) |
| 84 | Experimental research of concrete floor blocks with crushed bricks and tiles aggregate | 5.8 | 35 | Citations (PDF) |
| 85 | Comparative investigation on the influence of spent foundry sand as partial replacement of fine aggregates on the properties of two grades of concrete | 5.8 | 95 | Citations (PDF) |
| 86 | Design and development of self-compacting concrete made with coal bottom ash | 1.1 | 22 | Citations (PDF) |
| 87 | Recent advances in understanding the role of supplementary cementitious materials in concrete | 10.0 | 1,147 | Citations (PDF) |
| 88 | Mechanical properties and microstructural analysis of cement mortar incorporating marble powder as partial replacement of cement | 5.8 | 196 | Citations (PDF) |
| 89 | Effect of low-calcium coal bottom ash as fine aggregate on microstructure and properties of concrete | 0.1 | 5 | Citations (PDF) |
| 90 | Utilization of Industrial By-products in Concrete | 1.3 | 187 | Citations (PDF) |
| 91 | Lime Activated Fly Ash Paste in the Presence of Metakaolin | 1.3 | 10 | Citations (PDF) |
| 92 | Strength properties and micro-structural properties of concrete containing coal bottom ash as partial replacement of fine aggregate | 5.8 | 253 | Citations (PDF) |
| 93 | Effect of carbon nanotubes on properties of cement mortars | 5.8 | 268 | Citations (PDF) |
| 94 | Microstructure and properties of concrete using bottom ash and waste foundry sand as partial replacement of fine aggregates | 5.8 | 295 | Citations (PDF) |
| 95 | Compressive strength, drying shrinkage and chemical resistance of concrete incorporating coal bottom ash as partial or total replacement of sand | 5.8 | 146 | Citations (PDF) |
| 96 | Strength and microstructure analysis of bacterial treated cement kiln dust mortar | 5.8 | 33 | Citations (PDF) |
| 97 | Influence of bacterial treated cement kiln dust on the properties of concrete | 5.8 | 49 | Citations (PDF) |
| 98 | Use of waste copper slag, a sustainable material | 2.4 | 204 | Citations (PDF) |
| 99 | Permeation properties of concrete made with fly ash and silica fume: Influence of ureolytic bacteria | 5.8 | 129 | Citations (PDF) |
| 100 | Compressive strength, water absorption, sorptivity, abrasion resistance and permeability of self-compacting concrete containing coal bottom ash | 5.8 | 155 | Citations (PDF) |
| 101 | Effect of coal bottom ash as partial replacement of sand on properties of concrete | 7.6 | 268 | Citations (PDF) |
| 102 | Micro-structural and metal leachate analysis of concrete made with fungal treated waste foundry sand | 5.8 | 50 | Citations (PDF) |
| 103 | Influence of Fungus on Properties of Concrete Made with Waste Foundry Sand | 1.9 | 29 | Citations (PDF) |
| 104 | Fuzzy logic modeling of compressive strength of high-strength concrete (HSC) with supplementary cementitious material | 1.1 | 18 | Citations (PDF) |
| 105 | Utilization (recycling) of iron and steel industry by-product (GGBS) in concrete: strength and durability properties | 2.4 | 84 | Citations (PDF) |
| 106 | Mechanical and durability properties of self-compacting concrete containing fly ash and bottom ash | 1.1 | 26 | Citations (PDF) |
| 107 | Properties of concrete made with volcanic ash | 7.6 | 90 | Citations (PDF) |
| 108 | Influence of bacteria on the compressive strength, water absorption and rapid chloride permeability of concrete incorporating silica fume | 5.8 | 209 | Citations (PDF) |
| 109 | Utilization of wood ash in concrete manufacturing | 7.6 | 204 | Citations (PDF) |
| 110 | Use of iron and steel industry by-product (GGBS) in cement paste and mortar | 7.6 | 225 | Citations (PDF) |
| 111 | Effect of waste foundry sand (WFS) as partial replacement of sand on the strength, ultrasonic pulse velocity and permeability of concrete | 5.8 | 223 | Citations (PDF) |
| 112 | Influence of bacteria on the compressive strength, water absorption and rapid chloride permeability of fly ash concrete | 5.8 | 408 | Citations (PDF) |
| 113 | Abrasion resistance and strength properties of concrete containing waste foundry sand (WFS) | 5.8 | 127 | Citations (PDF) |
| 114 | Properties of concrete containing fungal treated waste foundry sand | 5.8 | 60 | Citations (PDF) |
| 115 | Effect of polyester fibres on the compressive strength and abrasion resistance of HVFA concrete | 5.8 | 117 | Citations (PDF) |
| 116 | Influence of water/powder ratio on strength properties of self-compacting concrete containing coal fly ash and bottom ash | 5.8 | 140 | Citations (PDF) |
| 117 | Properties of self-compacting-concrete containing fly ash subjected to elevated temperatures | 5.8 | 89 | Citations (PDF) |
| 118 | Effects of elevated temperatures on properties of self-compacting-concrete containing fly ash and spent foundry sand | 5.8 | 97 | Citations (PDF) |
| 119 | Properties of concrete containing ground granulated blast furnace slag (GGBFS) at elevated temperatures | 7.5 | 204 | Citations (PDF) |
| 120 | Use of cement kiln dust in cement concrete and its leachate characteristics | 7.6 | 140 | Citations (PDF) |
| 121 | Investigation of slag cement quality through the analysis of its efficiency coefficient | 1.7 | 7 | Citations (PDF) |
| 122 | Influence of metakaolin and silica fume on the heat of hydration and compressive strength development of mortar | 3.7 | 158 | Citations (PDF) |
| 123 | Utilization of silica fume in concrete: Review of durability properties | 7.6 | 348 | Citations (PDF) |
| 124 | Calcium carbonate precipitation by different bacterial strains | 0.3 | 85 | Citations (PDF) |
| 125 | Effect of volcanic ash on the properties of cement paste and mortar | 7.6 | 74 | Citations (PDF) |
| 126 | Prediction of compressive strength of self-compacting concrete containing bottom ash using artificial neural networks | 4.6 | 275 | Citations (PDF) |
| 127 | Effect of metakaolin and foundry sand on the near surface characteristics of concrete | 5.8 | 62 | Citations (PDF) |
| 128 | Influence of high temperature on the properties of concretes made with industrial by-products as fine aggregate replacement | 5.8 | 108 | Citations (PDF) |
| 129 | Strength, durability, and micro-structural properties of concrete made with used-foundry sand (UFS) | 5.8 | 151 | Citations (PDF) |
| 130 | Effect of ureolytic bacteria on concrete properties | 5.8 | 305 | Citations (PDF) |
| 131 | Properties of self-compacting concrete containing class F fly ash | 4.7 | 267 | Citations (PDF) |
| 132 | Use of silicon and ferrosilicon industry by-products (silica fume) in cement paste and mortar | 7.6 | 91 | Citations (PDF) |
| 133 | Utilization of waste foundry sand (WFS) in concrete manufacturing | 7.6 | 189 | Citations (PDF) |
| 134 | Utilization of silica fume in concrete: Review of hardened properties | 7.6 | 573 | Citations (PDF) |
| 135 | Waste foundry sand and its leachate characteristics | 7.6 | 138 | Citations (PDF) |
| 136 | Utilization of municipal solid waste (MSW) ash in cement and mortar | 7.6 | 99 | Citations (PDF) |
| 137 | Utilization of coal combustion by-products in sustainable construction materials | 7.6 | 109 | Citations (PDF) |
| 138 | Use of municipal solid waste ash in concrete | 7.6 | 118 | Citations (PDF) |
| 139 | Effect of metakaolin on the near surface characteristics of concrete | 2.3 | 23 | Citations (PDF) |
| 140 | Thermo-mechanical characteristics of concrete at elevated temperatures up to 310°C | 1.6 | 57 | Citations (PDF) |
| 141 | Utilization of waste materials and by-products in producing controlled low-strength materials | 7.6 | 108 | Citations (PDF) |
| 142 | Effect of used-foundry sand on the mechanical properties of concrete | 5.8 | 257 | Citations (PDF) |
| 143 | Permeability of high-performance concrete subjected to elevated temperature (600°C) | 5.8 | 133 | Citations (PDF) |
| 144 | Influence of metakaolin on the properties of mortar and concrete: A review | 3.7 | 831 | Citations (PDF) |
| 145 | Abrasion resistance and mechanical properties of high-volume fly ash concrete | 2.3 | 74 | Citations (PDF) |
| 146 | Damage in granite under heating/cooling cycles and water freeze–thaw condition | 5.3 | 242 | Citations (PDF) |
| 147 | Utilization of spent foundry sand in controlled low-strength materials and concrete | 7.6 | 145 | Citations (PDF) |
| 148 | Use of recycled plastic in concrete: A review | 5.5 | 964 | Citations (PDF) |
| 149 | Modeling properties of self-compacting concrete: support vector machines approach | 0.6 | 18 | Citations (PDF) |
| 150 | Utilization of cement kiln dust (CKD) in cement mortar and concrete—an overview | 7.6 | 127 | Citations (PDF) |
| 151 | Résistances mécaniques et abrasion de bétons de cendres volantes | 0.0 | 0 | Citations (PDF) |
| 152 | Properties of concrete containing scrap-tire rubber – an overview | 5.5 | 863 | Citations (PDF) |
| 153 | Properties of concrete incorporating high volumes of class F fly ash and san fibers | 10.0 | 55 | Citations (PDF) |
| 154 | Performance characteristics of high-volume Class F fly ash concrete | 10.0 | 545 | Citations (PDF) |
| 155 | Effect of fine aggregate replacement with Class F fly ash on the mechanical properties of concrete | 10.0 | 254 | Citations (PDF) |
| 156 | Effect of fine aggregate replacement with Class F fly ash on the abrasion resistance of concrete | 10.0 | 139 | Citations (PDF) |
| 157 | Long-Term Performance of High-Volume Fly Ash Concrete Pavements | 0.1 | 9 | Citations (PDF) |
| 158 | Solvation of thiocyanate complexes of tungsten(VI) by 5-(4-pyridyl) nonane from aqueous hydrochloric acid solutions | 1.1 | 1 | Citations (PDF) |
| 159 | High strength concrete and the impact of metakaolin on its mechanical, durability and microstructural characteristics – A review | 2.3 | 1 | Citations (PDF) |
| 160 | Evaluation of Machine Learning Approaches for Hydration Heat Prediction in Energy-Efficient Cement Composites | 2.4 | 4 | Citations (PDF) |
| 161 | Structural fire performance of RC beams via direct coupled temperature-displacement nonlinear simulation | 2.4 | 3 | Citations (PDF) |
| 162 | Comparative study of NFC with different coarse aggregate sizes by Taguchi grey method | 0.5 | 0 | Citations (PDF) |
| 163 | Volcanic basalt quarry dust as a sustainable precursor for low-carbon geopolymer concrete | 1.1 | 0 | Citations (PDF) |
| 164 | Effect of high-volume fly ash on the engineering properties of pervious concrete – A techno-sustainability assessment | 5.8 | 2 | Citations (PDF) |
| 165 | Review of the Properties of Cement-Based Composites with Carbon-Based Nanomaterials for Potential Functional Applications. | 2.1 | 2 | Citations (PDF) |
| 166 | LABVIEW BASED REAL-TIME DATA AQUISITION SYSTEM FOR INDUSTRIALPROCESS MANAGEMENT | 0.1 | 0 | Citations (PDF) |
